Product Description

Technical parameters:
 

model	thrust	speed	push distance	motor model
10	10	60	40	JW5012

Product Introduction:

The electric actuator is a reciprocating actuator driven by a motor. It is suitable for all linear motion which needs
reciprocating and pushing. It can swing and rotate by means of other connecting rods. It has overload
protection (mechanical and electrical overload protection) It is widely used in metallurgy, electric power, coal,
chemical and other industries. It is widely used in metallurgy, electric power, coal, chemical industry and so on,
with the advantages of light weight, strong pulling force, low noise, low energy consumption and convenient
installation and maintenance. , Especially for long-distance, high-altitude and dangerous situations instead of
hydraulic, pneumatic devices, can be operated separately on-site and centralized control.
Because the nut is fixed relative to the push rod, the screw moves the push rod linearly along the CZPT rail in
the CZPT sleeve so as to make the push rod reciprocate. As a result, Push and pull action.

Our company produced the DT type, HDG series of electric putt (electric cylinder). Push (pull) force from
0.25KN to 50KN; push and pull stroke speed were 25mm / s, 42mm / s, 84mm / s. Is a smooth and accurate
action, reliable performance, and has built-in overload protection of the mechanical rotation device. In a very
wide range of areas can replace or replace the cylinder, the cylinder, especially in high temperature, fire,
explosion-proof, pollution-free environmental conditions, is an indispensable supporting equipment.
The series, the specifications of the push and pull stroke size or speed (0-100mm / s) can be selected by the
user.
To facilitate automatic control or to achieve a special trajectory, according to user requirements, can be
configured DC, frequency, step, speed and other special motor to meet the total control requirements.
Products are widely used in electricity, machinery, metallurgy, transportation, coal, chemicals, food processing
and other departments. 

Technical specification:
 

NO.	Type	Trust (kg)	Route (mm)	Speed (mm/s)	Motor		380(V)		Le(mm)		contour dimension (L*W*H)mm	weight (kg)
					Type	Power (w)	Revolution (T/Min)	Electricity (A)	LeMin	LeMax
1	25-20-I	25	200	48	AO25571	40	1400	0.23	369	569	580*125*118	7.5
2	25-20-II	25	200	96	AO25571	60	2800	0.23	369	569	580*125*118	7.5
3	100-40-I	100	400	42	AO5624	120	1400	0.47	640	1040	858*152*206	23
4	100-40-II	100	400	84	AO5622	180	2800	0.52	640	1040	858*152*206	23
5	300-50-I	300	500	42	AO6334	370	1400	1.12	745	1245	998*170*226	35
6	300-50-II	300	500	84	AO6332	550	2800	1.38	745	1245	998*170*226	35
7	500-50-I	500	500	50	AO7134	750	1400	2.02	778	1278	1098*190*226.5	52
8	500-50-II	500	500	100	AO7132	1100	2800	2.6	778	1278	1098*190*226.5	52
9	700-60-I	700	600	50	AO7134	750	1400	2.02	803	1343	1193*200*279	63
10	700-60-II	700	600	100	AO7132	1100	2800	2.6	803	1343	1193*200*279	63
11	1000-60-I	1000	600	50	JO2-21-4	1100	1400	2.68	883	1483	1260*204*271	75
12	1000-60-II	1000	600	100	JO2-21-2	1500	2860	3.24	883	1483	1260*204*271	75
13	1600-80-I	1600	800	50	JO2-31-4	2200	1400	4.9	1063	1863	1535*302*330
14	1600-80-II	1600	800	100	JO2-31-2	3000	2860	8.06	1063	1863	1535*302*330

Picture

ABOUT US

 

Bushing Application, Type and Compression Capability

Bushings are cylindrical bushings used in machinery. It prevents wear of moving parts and is often used as an enclosure. Bushings are also known as plain bearings or sleeve bearings. You may be wondering what these parts do and how they work, but this article aims to answer all your questions. We'll cover bushing applications, types and compression capabilities so you can choose the right 1 for your needs.

application

A bushing is a mechanical component that plays an important role in many different fields. In addition to being very practical, it helps reduce noise, vibration, wear and provides anti-corrosion properties. These properties help mechanical equipment in various ways, including making it easier to maintain and reducing its overall structure. The functionality of an enclosure depends on its purpose and environment. This article will discuss some of the most common applications of casing.
For example, in an aircraft, the bushing assembly 16 may be used for the bulkhead isolator 40 . The bushing assembly 16 provides the interfaces and paths required for current flow. In this manner, the sleeve assembly provides a secure, reliable connection between 2 objects with different electrical charges. They also prevent sparking by increasing the electrical conductivity of the component and reducing its resistivity, thereby minimizing the chance of spark formation.
Another common application for bushings is as a support shaft. Unlike bearings, bushings operate by sliding between 2 moving surfaces. As a result, they reduce friction and handling stress, reducing overall maintenance costs. Typically, the bushing is made of brass or bronze. The benefits of bushings are similar to those of bearings. They help extend the life of rotating machines by reducing frictional energy loss and wear.
In addition to identifying growth opportunities and minimizing risks, the Bushing Anti-Vibration Mounts Market report provides insights into the dynamics of the industry and its key players. The report covers global market size, applications, growth prospects, challenges and regional forecasts. The detailed section on Bushing Anti-Vibration Mounts industry provides insights on demand and supply along with competitive analysis at regional and country level.

type

There are several types of bushings. Among them, the SF6 insulating sleeve has the simplest structure and is based on composite hollow insulators. It also has several metal shielding cylinders for regulating the electric field within the enclosure and another for grounding the metal shield. In addition to being lightweight, this sleeve is also very durable, but the diameter of its shield electrode is very large, which means special installation and handling procedures are required.
Linear bushings are usually pressed into the bore of the shaft and provide support as the shaft moves in/out. Non-press-fit bushings are held in place by snap rings or pins. For certain applications, engineers often choose bushings over bearings and vice versa. That's why. Below are some common bushing types. If you need to buy, make sure you know how to tell them apart.
OIP bushings are used for oil-filled cable boxes, and oil-to-oil bushings are used for EHV power transformers. The main components of the OIP enclosure are shown in Figure 7a. If you are considering this type of bushing for your specific application, you need to make sure you understand your specific requirements. You can also consult your local engineering department for more information.
All types of bushings should be tested for IR and capacitance. The test tap should be securely attached to the bushing flange. If damaged bushings are found, replace them immediately. Be sure to keep complete records of the enclosure for routine maintenance and any IR testing. Also, be sure to pay attention to tan d and thermal vision measurements.

Compressive ability

There are several things to consider when choosing an enclosure. First, the material. There are 2 main types of bushings: those made of filled Teflon and those made of polyester resin. The former has the highest compressive strength, while the latter has a lower compressive capacity. If you need small amounts, glass-filled nylon bushings are the most common and best option. Glass-filled nylon is an economical material with a compressive strength of 36,000 lbs.
Second, the material used for the enclosure must be able to withstand the load. For example, bronze bushings can cause metal shavings to fall into the papermaking process. CG materials can withstand very high levels of moisture, which can damage bushings that require lubrication. Additionally, these materials can operate for extended periods of time without lubrication. This is particularly advantageous in the paper industry, since the casing operates in a humid environment.
In addition to the material and its composition, other characteristics of the enclosure must also be considered, including its operating temperature. Although frictional heat from moving loads and the temperature of the bushing itself can affect the performance of the bushing, these factors determine its service life. For high temperature applications, the PV of the enclosure should be kept low. On the other hand, plastic bushings are generally less heat resistant than metal bushings. In addition, plastic sleeves have a high rate of thermal expansion. To avoid this, size control is also important.
Low pressure bushings have different requirements. An 800 MVA installation requires a low voltage bushing rated at 14 000 A. The palm assembly of the transformer also features a large central copper cylinder for electrical current. The bushing must withstand this amount of current and must maintain an even distribution of current in the transformer tank. If there is a leak, the bushing must be able to resist the leak so as not to damage the transformer.

cost

The cost of new control arm bushings varies widely. Some parts are cheaper than others, and a new part is only $200. However, if you replace the 4 control bushings in your car, the cost can exceed $1,200. The cost breakdown for each section is listed below. If you plan to replace all four, the cost of each bushing may range from $200 to $500.
The control arm bushing bears the brunt of the forces generated by the tire and is parallel to the direction of the force. However, over time, these components wear out and need to be replaced. Replacing 1 control arm bushing costs between $300 and $1,200. However, the cost of replacing each arm bushing depends on your car model and driving habits. The control arm bushings should last about 100,000 miles before needing replacement.
The repair process for control arm bushings is time consuming and expensive. Also, they may need to remove the heat shield or bracket. In either case, the procedure is simple. Stabilizer bar brackets are usually attached with 1 or 2 mounting bolts. They can also be secured with nuts or threaded holes. All you need is a wrench to remove them.
The control arm bushings are made of 2 metal cylinders and a thick rubber bushing. These parts can deteriorate from potholes, off-roading or accidents. Because they are made of rubber, the parts are more expensive than new. Buying used ones can save you money because you don't need to install them yourself. However, if you do plan on fixing a luxury car yourself, be sure to find 1 that has a warranty and warranty.

maintain

To prevent your vehicle from overheating and leaking oil, a properly functioning bushing must be used. If the oil level is too low, you will need to check the mounting bolts to make sure they are properly tightened. Check gasket to ensure proper compression is applied, replace bushing if necessary. You should notify your vehicle manufacturer if your vehicle is immersed in oil. Whenever an oil leak occurs, it is very important to replace the oil-filled bushing.
Another important aspect of bushing maintenance is the detection and correction of partial discharges. Partial discharge is caused by current entering the bushing. Partial discharge can cause tree-like structures, cracks and carbonization in the discharge channel, which can eventually damage the casing. Early detection of these processes is critical to ensuring that your vehicle's bushings are properly maintained. Identifying and repairing partial discharges is critical to ensuring optimal operation, regardless of the type of pump or motor.
To diagnose casing condition, perform several tests. You can use tan d measurement, which is a powerful tool for detecting the ingress of water and moisture. You can also use power factor measurements to detect localized defects and aging effects. You can also check the oil level by performing an infrared check. After completing these tests, you will be able to determine if there is enough oil in the casing.
If the oil level in the transformer is too low, water and air may leak into the transformer. To avoid this problem, be sure to check the MOG and transformer oil levels. If the silicone is pink, replace it. You should also check the function of the oil pump, fan and control circuits annually. Check the physical condition of the pump and fan and whether they need to be replaced. Clean the transformer bushing with a soft cotton cloth and inspect for cracks.